Tyco Electronics designs, manufactures and markets engineered electronic components, these are passive electronic components which include connectors and interconnect systems, relays, switches, circuit protection devices, touchscreens, sensors, and wire and cable.
Tyco Electronics – TE Connectivity
- Electronic Components, Electromechanical
- Copper and Fiber Network Solutions
- Advanced Communications Systems
Rugged Fiber Optics enable data delivery at high speed and over long distance to a level not possible with traditional copper cable…
TE’s ASIC (application-specific integrated circuit) to ASIC end-to-end solutions include a comprehensive range of connectors, cables, Optical Flex Circuitry, routers, switches, passive, active and electro optic devices
SuperDrum integrated reels, which integrate cables, connectors, and media conversion.
TE AD&M Fiber Optics Product & Application Summary
This product solution set employs electro optic devices such as switch / routers inclusive of Wavelength Division Multiplexing, active devices, as well as harness and interconnect designs that employ low loss / low noise Physical Contact and or Expanded Beam connectors and fiber optic cable designs
Here is a 12V, 25A, Single Output Isolated DC/DC Converter, Positive polarity from Murata Power.
HPQ-12/25-D48PBH-C – Murata Power Solutions
“Advanced automated surface mount assembly and planar magnetics deliver galvanic isolation rated at 2250 Vdc for basic insulation. To power digital systems, the outputs offer fast settling to current steps and tolerance of higher capacitive loads. Excellent ripple and noise specifications assure compatibility to CPU’s, ASIC’s, programmable logic and FPGA’s. ..”
- Industry standard quarter brick 2.3 x 1.45 x 0.49 open frame package
- Wide range 36 to 75 V DC input voltages with 2250 Volt Basic isolation
- Up to 300 Watts total output power
- High efficiency (94.5%) synchronous rectifier topology
- Stable no-load operation with no required external components
A 250 watt, open frame, single output AC/DC power supply in an industry standard 4 x 7 format. This chassis mount power supply has a 85-264 AC volt Wide-range input AC input with power factor correction.
It is medical rated with an operating temperature range of 0 – 70 °C and up to 86% efficiency. The NLP250N-99S12J is Rohs 6/6 compliant.
- AC Input – Wide-range Inputs: 85 – 264 AC
- Outputs: – 12 Volts, 21 Amps, 250 Watts.
- Efficiency: – 86%
- Dimensions (L x W x H) – 7 x 4 x 1.5 in
Sager Power Systems
Sager Power Systems is a specialized group within Sager Electronics focused solely on power supplies. They offer over 15,000 world-class AC/DC and DC/DC standard solutions from leading power supply manufacturers, and is able to evaluate and specify standard and value added solutions.
This sensor is based on a unique capacitive cell, this affordable sensor is used in applications such as office automation, HVAC and home appliances and process control too.
HS1101LF Humidity Sensor – Measurement Specialties
This sensor sports a fast response time and very low temperature coefficient. It also has High reliability and long term stability of Parameters.
Humidity Measuring Range 1% – 99% RH. Nominal capacitance at 55% RH is 180 pF.
A Humidity to Frequency Convertor to make a Easy Digital Counter or Embedded Interface using the venerable 555 is shown below.
Correction – R4=49.9kΩ / RV1=50 kΩ potentiometer.
“Measurement Specialties is a global designer and manufacturer of sensors and sensor-based systems which measure pressure/force, position, vibration, temperature, humidity, and fluid properties.”
1000, Lucas Way Hampton, VA 23666 United States.
This water proof, chemical resistant, low drift Humidity and Temperature module from IST :provides a fully calibrated and compensated humidity and temperature digital signal output.
HYT 271 Humidity Temperature Module – IST AG
The Digital output is for a I2C interface in a 14 bit resolution. Accuracy at 23 °C is +/- 1.8 % RH in the span of 0 % RH to 80 % RH. This reading comes with a Response time of less than 4 seconds.
They also have a LabKit with USB Interface to evaluate and implement in your system.
“The Labkit was developed as a Plug&Play tool for a fast evaluation of the HYGROCHIP digital humidity sensors. The ready-to-use system consists of a PC-adapter with an USB connecting wire, a connection adapter with plugs for all product variants.”
Component level. manufacturer of thin-film RTD temperature sensors, capacitive humidity sensors, mass flow sensors and conductivity sensors.
Innovative Sensor Technology IST AG
Stegrütistrasse 14 9642 Ebnat-Kappel Switzerland
Versatile and Replaceable Digital humidity sensor, a cost-effective component. In the SHT family the capacitive humidity sensors are fully calibrated and provides a digital output ready for interface.
Digital Humidity and Temperature Sensor SHT71
Each SHT7x is individually calibrated in a precision humidity chamber. The calibration coefficients are programmed into an OTP memory on the chip. These coefficients are used to internally calibrate the signals from the sensors. The 2-wire serial interface and internal voltage regulation allows for easy and fast system integration.
The power consumption of around 80uW makes it ideal for battery operated devices. It measures the full span of 0-100% RH with a response time of 8 sec. The temperature range being -40 – +125°C.
SCK is used to synchronize the communication between microcontroller and SHT7x. The DATA tri-state pin is used to transfer data in and out of the sensor.
Sensirion is the leading manufacturer of high-quality sensors and sensor solutions for the measurement and control of humidity, and of gas and liquid flows.
Laubisruetistrasse 50, 8712 Staefa ZH, Switzerland.
MZS is an EMI RFI Filter for equipment designed to conform EMI regulations such as VCCI, CISPR, FCC, EN, etc. These are mounted within Control Panels or Cabinets. Metal Enclosures that are grounded are Ideal for use along with this filter.
MZS Single Phase Noise Filter – TDK Lambda
Swicth Boards and Meter Boxes also can use this for lines going to Sensitive Equipment. These along with MCB and ELCB make Mains Power Safer and Cleaner. – delabs
- Attenuation effect against high voltage pulse noise.
- Attenuates conductive emission from power supply.
- Leakage current:1mA max..(250V,60Hz)
- Rated Current – 6-20A Type Numbers
- Leakage Current 1mA max at AC250V 60Hz
from TDK Lambda
3-9-1, Shibaura, Minato-ku, Tokyo 108-0023, JAPAN